This is a question our experts keep getting from time to time. Now, we have got the complete detailed explanation and answer for everyone, who is interested!
It is necessary to have terminators installed at both ends of the backbone cable.
Which of the following network topologies does not call for the use of a terminator?
The bus topology is considered to be one of the first application kinds of the ethernet, now that we are familiar with the two different topologies. It uses fewer cables than the star topology, but if the main cable goes down, it means that the entire network is offline as a result. Additionally, it necessitates the use of terminators on the cable termination points.
Which topology of the network makes use of terminators?
A bus topology includes all of the devices being connected to one another via a single central cable. This cable is referred to as the backbone. In order to prevent the electrical signal from being reflected back along the cable, terminators are attached to its severance point. With a topology known as a bus, the signal that is transmitted via the primary wire is received by all of the devices that are connected.
Which topology must be utilized so that the process can end?
In a architecture known as a bus, all of the computers connect to the network through a single line. In order to prevent signal reflection, the cable needed to have both of its ends terminated. 2.
What network needs terminator?
(1) An apparatus that is connected to the terminals of a bus network or a daisy chain. It is the job of the terminator to take in signals and process them in such a way that they do not get reflected back down the line. Terminators are necessary components for both ends of the bus in Ethernet networks, whereas SCSI chains only require a single terminator at the final link in the chain.
Network Topologies
26 questions found in related categories
Which network topology necessitates the expenditure of money?
Which of the following network topologies calls for a central controller or hub? Explanation: In a star topology, no computer is directly connected to another computer; instead, all of the computers are connected to a single hub in the middle of the network.
Network terminators are able to?
With the CAN Terminator, you can put an end to a CAN (Controller Area Network) bus operating at high speed. This CAN Terminator has a female 9-pin D-Sub socket, a male 9-pin D-Sub connector, and a termination resistor with a value of 120 ohms. Every CAN network requires two terminators, one to be placed at each of the network’s ends.
Which topology of the network is the most efficient?
Ideally, the mesh topology should be the one that runs the quickest. Nonetheless, the star topology is considered to be the most effective.
Which topology is the most difficult when it comes to identifying faults?
Which topology is the most difficult when it comes to identifying faults? When using a bus topology, it is more difficult to identify where the problem lies.
Which topology is taught at educational institutions?
Ring topology for a network
Ring network topologies are utilized by the majority of educational institutions, while they are also utilized by some commercial enterprises. The technology known as FDDI, SONET, or Token Ring is usually utilized. The data is carried forward from each node, one bit at a time, until it reaches its final location.
Which topology results in the highest costs?
The use of a star topology to link a computer in a workgroup is by far the most common method. Because of how much the hub costs, it is quite pricey. The Star topology is the most expensive network to put up because it requires the highest number of cables and additionally requires the use of a trunk to protect the cables from damage.
What is the diagrammatic explanation of tree topology?
The term “tree topology” refers to a topology that is characterized by the presence of a tree structure and in which all of the computers are connected in the same manner as the tree’s branches. The term “tree topology” refers to the combination of a “Bus and Start” network topology in the context of a computer network.
Which topology makes use of terminators at both ends of the connection?
The Drawbacks of Using a Linear Bus Topology
It is necessary to have terminators installed at both ends of the backbone cable. If the whole network goes down, it will be difficult to figure out what the issue is.
Which topology is the most effective?
A full mesh topology is one in which each node on the network is connected to each and every other node on the network. This offers a network that is totally redundant and has the highest level of dependability of any network. In the event that one of the links or nodes in the network fails, there will be a backup route in place to ensure that network traffic is not disrupted.
What are the five different topologies for a network?
- Topology of Meshes
- Topology of the Stars
- Topology of the Bus
- Ring Topology.
- Hybrid Topology.
What exactly is topology, and what are its subfields?
The two primary categories of topologies that can be found in computer networks are as follows: In a computer network, the way in which individual computers, known as nodes, are connected to one another is referred to as the network’s physical topology…. Logical Topology: A logical topology is a diagram that describes how data moves from one computer to another.
Which topology offers the greatest degree of dependability?
Solution(By Examveda Team)
Mess The term “topology” refers to the configuration of a network in which every computer and networking device is interconnected with each other. This configuration makes it possible for the majority of transmissions to be spread, even if one of the connections fails.
Which topology is ideal for a local area network?
Star topology has become the primary physical topology for LANs. ARCNET was the network that first made widespread use of the star, and Ethernet followed suit later. As can be seen in Figure 5.17, each node has its own direct connection to a device in the network’s core, which could be a hub or a switch.
Which topology has less security?
Answer is “Bus”
What kind of network topology is used the most frequently today?
- By far the most typical configuration is a star topology…
- The bus topology, which is also known as the line or backbone topology, connects all of the devices with a single wire that only goes in one way…
- The name of this topology gives away the fact that all of the nodes are organized in the form of a ring.
What exactly does “topology diagram” mean?
A network topology diagram is a graphical representation of a network’s devices, connections, and pathways. This type of diagram allows you to visualize how devices are connected to one another and how they communicate with one another. Performance and stability are both affected differently by a variety of various topologies. The following topologies are the most common: The topology of the bus
What exactly is meant by “star Bus topology”?
The term “Star Bus” refers to a networking topology in which multiple workgroup or departmental local area networks (LANs) are combined into a single network by connecting their hubs to one another via a network bus. The term “star bus topology” refers to a hybrid architecture that combines “star topology” with “backbone bus topology.”
The 120 ohm terminator can be used, right?
At the very least inside the CAN community, it is common knowledge that each and every CAN and CAN FD network ought to be terminated with a 120 Ohm resistor situated at each end of the bus…. You should see a reading of roughly 60 Ohms if the termination is done correctly.
Which type of topology does CAN employ?
The CAN standard is compatible with a variety of topologies. Line and bus topologies are two of the most common types of topologies. Topology of the Stars
CAN bus with sixty ohms?
The most typical problem with CAN-Bus networks is that the termination resistance is either too high or too low. You should get a reading of 60 ohms across these two wires because there are two resistors with a value of 120 ohms that are connected in parallel.